Heat | Cast Iron Kitchen Sinks

Archive for the ‘heat’ tag

Manifold Radiant Floor

Manifold Radiant Floor
Manifold Radiant Floor Manifold Radiant Floor

An Overview of the Underfloor Heating Schema

Underfloor heating is a modernized heating concept, which perhaps owes its origin to the Roman times. It is believed that in those days, civilizations constructed their structures with voids, which enabled circulation of warm air, heated due to the open fire outside, thus maintaining high temperatures inside the premises. Since then times have changed, however one aspect has remained constant and that is the desire to be comfortable in all circumstances, even if the stated required adapting the older methods. The advanced adaptations, like in the case of underfloor heating, proved to be obviously superior and much better conceptualised to enable complete luxury.

The Case of Underfloor Heating

As enumerated above, underfloor heating is a mechanically sophisticated version of the ancient principle, which was aimed at creating a warm inside temperature zone. Presently it is being extensively used throughout Europe, to uniformly heat residential and commercial properties. Herein, the heating equipment is embedded inside the floor, which utilizes the heat conduction and radiant heat mechanisms to control the internal climate. The heating system in this concept could be warm water based or electricity driven, depending upon the precise requirements. In either of the situations, underlying mechanism is almost identical, save few specific system features.

Warm Water Based

In this heating methodology, pipes or tubes are laid into the floor through which warm water circulates and thus coverts the base to a radiant surface. This system is based on a low temperature range say 50OC. The entire setup might accompany higher installation charges, however in the long run, owing to the energy saving features, the economical aspects balance to ensure cost savings. The stated structure offers complete flexibility in terms of pipe types, installation specifics and the control options.

Electrical Systems

An electrical system of underfloor heating works on a similar mechanism, the key difference being the mode of heating. Herein, rather than warm water, electric cable or a heating element is used to generate the same results. The system is cheaper in terms of installation charges, and it also takes less time to install the electric underfloor heating.

Advantages

With the particulars of underfloor heating mechanism outlined, it is now imperative to be precisely clear upon the various positives of this system and thus take a final call. The foremost benefit as extended by this heating model is the comfort level extended. Unlike the available substitutes, which work on a top down approach, underfloor heating works on the principle of bottom up schema. Also as the warm air convects, it losses approximately 2OC, thus creating ambience on the likes of natural surroundings.

Another key advantage of the system is explained from the setup aesthetics. The heating structure is in the floor and thus neither exposed nor bulky. Moreover, the setup is highly energy efficient which is critically important at both micro and macro levels.

The controlling of the system is not a tedious task. Some underfloor heating systems are sensitive to the room and floor temperature and thus adjust automatically to any external changes. The central manifold acts as the distribution point. Moreover, there are options in the category of individual room controls, which can take care of the specific room heating aspects.

With the stated in background, there certainly is a strong enough case in the favour in underfloor heating. The choice is between the available options in this category i.e. water based or electric. While both can suffice, the definite option can be best decided, post an analysis of details like construction type, heating requirements, etc. And underfloor heating continues to grow in popularity as more and more people realise the advantages the heating system has to offer them.

About the Author

Kurt Ashman wrote the Article 'An Overview of the Underfloor Heating Schema' and recommends you visit http://www.gardeningthoughts.co.uk for more information on electrical underfloor heating for log cabins.

would you recommend radiant floor cooling system in a house?

I am about to install a underfloor heating/cooling system, which is flexible pipes with a manifold, thermostats and a water chiller/heater.
For the heating i know that it is a perfect system if the floor temperature does not go above 30deg. Celsius, but for the cooling i have no idea, is it effective?
What would be the water temperature inside the pipes, knowing that i live in a very hot climate that can reach up to 47deg. Celsius, and the temperature inside the house should be around 22C.
Some people told me that specially in the basement (humidity) the floor can become slippery.
I need to know what is the recommended floor temperature for cooling and what is the recommended water temperature inside the pipes.
Thank you

I have to agree with the previous answerer. In floor heating would make sense, but I don't see how in floor cooling would do anything. In floor heating is actually very efficient because the heat will radiat and fill the area. Again I don't see how in floor colling would work unless it was placed on the second floor of a home and was used to coll the first floor, for the same reasons mentioned by the previous answerer.